BRC Solar Selects EPC 100 V eGaN® FETs for Next Generation Solar Optimizer
The 100 V EPC2218 GaN FETs alleviate space limitations to achieve higher frequency and power rating in BRC’s new M500/14 power optimizer
EL SEGUNDO, Calif.–(BUSINESS WIRE)–#GaN—BRC Solar GmbH has revolutionized the photovoltaic market with its power optimizer, increasing energy yield and performance of pv plants and systems. Designing-in Efficient Power Conversion’s EPC2218 100 V FETs into its next generation M500/14 power optimizer has enabled a higher current density due to the low power dissipation and the small size of the GaN FET making the critical load circuit more compact. The small parasitic capacitance and inductance of the GaN FETs creates a clean switching performance which allows good EMI behavior in the field. Another benefit of the GaN FETs is the zero reverse recovery losses.
The EPC2218 is a 100 V GaN FET, 3.2 mΩ, 231 Apulsed, with a small footprint of just 3.5 mm x 1.95 mm, offering lower losses and smaller size than comparable silicon MOSFETs for increased power density.
BRC’s previous range, the M400/12, handled currents up to 12 Amps and a maximum power operation at 400 watts. By changing from Si FETs to GaN FETs the company achieved an increase of output current to 14 Amps with a power rating of 500 watts – while keeping the same board size. Also, the switching frequency in the M500/14 is twice as high than the previous generation allowing for passive components, such as capacitors and inductors, to be decreased in value or even completely removed.
The company’s optimizer is only active when shading on the photovoltaic module appears. The predominant case is a fully irradiated module, where the circuit goes into an inactive state. The switching FET is continuously closed in this situation. It is important that the power losses on the board be kept as low as possible. Because of that, the EPC2218 is the optimal solution for BRC’s application because of its low RDS(on). The static losses are also extremely small thanks to the excellent conductivity of the GaN FET.
During the active mode the switching behavior of the module optimizer leads to a small and acceptable power loss. The low parasitic components of the EPC2218 enable fast and clean switching in the application.
In both modes, the temperature rise of the FET is small and allows good thermal transfer to the board via the LGA pads of the EPC2218 even at higher ambient temperatures. Therefore, an additional heatsink is not required further saving space and weight.
Winona Kremb from BRC Solar Gmbh, commented, “EPC’s eGaN FETs open a new horizon in the development of high-density power electronics. We will watch the further applications and products from EPC and are excited to be part of the journey.”
“Working with BRC has been an exciting design-in opportunity and, together with our distribution partner Finepower, we have been able to achieve great results moving the company from silicon to GaN. Designers using GaN can now take advantage of devices that are higher performance, smaller, more thermally efficient, and at a comparable cost,” added Stefan Werkstetter, VP of Sales, EMEA.
About EPC
EPC is the leader in enhancement mode gallium nitride (eGaN®) based power management. eGaN FETs and integrated circuits provide performance many times greater than the best silicon power MOSFETs in applications such as DC-DC converters, remote sensing technology (lidar), motor drives for eMobility, robotics, drones, and low-cost satellites.
Visit our website: www.epc-co.com
Follow EPC on social media: LinkedIn, YouTube, Facebook, Twitter, Instagram, YouKu
eGaN is a registered trademark of Efficient Power Conversion Corporation, Inc.
Contacts
Press contacts: Efficient Power Conversion:
Renee Yawger tel: +1.908.619.9678 email: renee.yawger@epc-co.com
EMEA contact: June Hulme Tel +44 (0) 7712 654009 email: june.hulme@epc-co.com
BRC Solar GmbH, Gehrnstrasse 76275, Ettlingen Germany
Contact: Winona Kremb, tel: +49 7243 924 1660, email: info@brc-solar.de
https://brc-solar.de
