Premium Motor Drive Performance at Low Cost for e-bikes, Drones, and Robotics with GaN FETs from EPC
The EPC9167 GaN-based inverter reference design enhances motor system performance, range, precision, torque, all while lowering overall system cost. The extremely small size of this inverter allows integration into the motor housing resulting in the lowest EMI, highest density, and lowest weight.
EL SEGUNDO, Calif.–(BUSINESS WIRE)–#Drones—EPC announces the availability of the EPC9167, a 3-phase BLDC motor drive inverter using the EPC2065 eGaN® FET. The EPC9167 operates from an input supply voltage between 14 V and 60 V (nominal 48 V) and has two configurations – a standard unit and a high current version:
- The EPC9167 standard reference design board is a 3-phase BLDC motor drive inverter board featuring the EPC2065 eGaN FET rated at 3.6 mΩ maximum RDS(on), 80 V maximum device voltage. This standard configuration uses single FETs for each switch position and can deliver up to 20 ARMS maximum output current.
- A high current configuration, the EPC9167HC, version of the reference design uses two paralleled FETs per switch position with the ability to deliver up to 42 Apk (30 ARMS) maximum output current.
Both versions of the EPC9167 contain all the necessary critical function circuits to support a complete motor drive inverter including gate drivers, regulated auxiliary power rails for housekeeping supplies, voltage, and temperature sense, accurate current sense, and protection functions. The boards also feature the ST Microelectronics, STDRIVEG600, smart motor drive GaN half-bridge driver.
The EPC9167 boards measure just 130 mm x 100 mm (including connector). The boards can also be configured for multiphase DC–DC conversion and support both phase and leg shunt current sensing.
Major benefits of a GaN-based motor drive are exhibited with these reference design boards, including lower distortion for lower acoustic noise, lower current ripple for reduced magnetic loss, lower torque ripple for improved precision, and lower filtering for lower cost. The EPC9167 boards’ lower weight and size enable incorporation of the drive into the motor housing and supports low inductance, higher power density motors.
EPC provides full demonstration kits, which include interface boards that connect the inverter board to the controller board development tool for fast prototyping that reduce design cycle times.
The default setting for the GaN-based motor drive kit is 100 kHz switching frequency and 14 ns deadtime. While the kit is designed to be programmed for different frequencies and deadtimes, operation at high frequency around 100 kHz allows for the elimination of electrolytic capacitors and the use of lower capacitance, and reduce the motor losses. Operating the boards with very small low deadtime of around 14 ns allows higher torque per ampere. The joint effect is to improve inverter and motor system efficiency of more than 7% vs. a silicon MOSFET solution which typically operates at 20 kHz and 500 ns deadtime.
“GaN-based inverters increase motor efficiency while reducing their cost and delivering the same performance as an expensive motor using a silicon MOSFET-based inverter,” said Alex Lidow, CEO of EPC. “This enables motor systems that are smaller, lighter, less noisy, have more torque, more range, and greater precision.”
Price and Availability
The EPC9167 reference design board is priced at $611.58 and the EPC9167HC reference design is priced at $678.78. Both are available for immediate delivery from Digi-Key at https://www.digikey.com/en/supplier-centers/epc
About EPC
EPC is the leader in enhancement mode gallium nitride (eGaN®) based power management. eGaN FETs and integrated circuits provide performance many times greater than the best silicon power MOSFETs in applications such as DC-DC converters, remote sensing technology (lidar), motor drives for eMobility, robotics, and drones, and low-cost satellites.
Visit our web site: www.epc-co.com
Follow EPC on social media: LinkedIn, YouTube, Facebook, Twitter, Instagram, YouKu
eGaN is a registered trademark of Efficient Power Conversion Corporation, Inc.
Contacts
Efficient Power Conversion:
Renee Yawger
tel: +1.908.619.9678
email: renee.yawger@epc-co.com
